Forceful Collisions Lab

PS
by POWER SOLAR0 views·Updated Mar 4, 2014
Powered by AI

Need to present on this topic?

Create your own polished presentation in minutes. Just describe what you need.

Free to try, no credit card required

Transcript

Thanks for watching

Forceful Collisions Lab

Any questions?

By: Tanner & Hannah

Materials

Hypothesis & Variables

Background Info

Hypothesis: If we change the height of release, then the distance and time will change.

Independent Variable: Height of Release

Dependent Variables: Distance, Force, Momentmeum, Velocity, Acceleration, & Time

Constants: Mass of Cart and the disk

  • Cart
  • Ramp
  • Meter Stick
  • Triple-Beam Balance
  • Ring Clamp
  • Ring Stand
  • Masking Tape
  • Motion Sensor
  • Computer
  • Various Masses

The mass production of cars began in the 1920s. There have been many safety devices introduced since then, but there is still room for improvement. In 1935, flashing turn signals were added to cars. In the 1950s, cruise control became popular. In the 1970s, air bags became a standard for all cars. In the future, we hope to see stronger glass used for the windows of cars to better protect passengers.

Works Cited

"Automobile." Encyclopedia Americana. Grolier Online, 2014. Web. 21 Feb. 2014.

Hounshell, David A. "Mass Production." Encyclopedia Americana. Grolier Online, 2014. Web. 21 Feb. 2014.

"Safety, Automotive." Grolier Multimedia Encyclopedia. Grolier Online, 2014. Web. 21 Feb. 2014.

Results- Data Table

Results- Calculations Table

Introduction

Procedure

  • Open Logger Lite
  • Measure 1 meter on the ramp and mark it
  • Measure the mass of the cart and disk and record them
  • Adjust the height of the starting point
  • Control: .3 meters
  • Trial 1: .15 meters
  • Trial 2: .45 meters
  • Trial 3: .6 meters

Ever since automobiles began to be mass produced, many strides have been made to increase safety in cars. One way to do so is to reduce the impact force during collisions. In this lab, we determined the impact force of a cart by crashing it into walls. It was our job to figure out how to reduce impact force.

Procedure (Part 2)

  • Set up motion sensor
  • Hold front wheels at the 1 meter mark
  • Press "collect" and release cart
  • Record time
  • Calculate for velocity,acceleration, force, and momentum
  • Repeat

Discussion Questions

Conclusion

Reults Summary

Q1: What was the purpose of doing the control?

A1: The purpose was to have something to compare the other trials to.

Q2: Compare results for the force of the various trials. Which trial had the least force? Why?

A2: The height that brought the lowest amount of force was 15cm(.15m). This is because gravity didn't have to pull very hard to bring the cart lower because the cart was already lower.

Q3: What is the importance of keeping everything constant between trials except for the independent variable?

A3: If you change more than one variable, you won't know what caused the change to happen.

Our hypothesis was "If you change the height of release then the distance and the time will change." Our hypothesis was proved correct by our experiment. I think that it was correct the height affects the angle at which the car travels downward. Our problem question was "Will the height of the ramp affect the force of impact?" I think the height of the ramp affected the force of impact because the force of gravity would be weaker if the ramp were lower

We tested to see whether or not changing the height of the ramp would change the force of impact.We tested the height of the ramp at 15cm, 45cm, and 60cm with 30cm as a control.

The control acheived a velocity of 1.07m/s, an acceleration of

1.19 m/s*, a force of .41N, and a momentum of .37kg*m/s

At 15cm, the cart achieved a velocity of .63 m/s, an accleration of .7m/s*, a force of .24N, and a momentum of .22 kg*m/s

At 45cm, the cart achieved a velocity of 2.29 m/s, an acceleration of 1.53 m/s*, a force of .53N, and a momentum of .8 kg*m/s

At 60cm, the cart achieved a velocity of 2 m/s, an acceleration of 4m/s*, a force of 1.4N, and a momentum of .7 kg*m/s

Discussion Questions continued

Discussion Continued

Q7: What would have happened to the momenteum if the velocity of you cart was higher?

A7: The cart would have recoiled more because it would gain more momenteum.

Q8: What are 2 improvements that could be made with the set up or procedure if you were to do it again?

A8: We would change the current equipment for more stable equipment. We would also change how many times we tested each trial as to improve accuracy.

Q4: What is a different indepent variable that you could have chosen for this activity?

A4: We could change the tires on the cart of the surface of the board

Q5: Explain how Newton's first law applies to a car crash.

A5: When a car makes contact it wants to keep going so it recoils back because it still has momenteum.

Q6:Did the momenteum of the cart change very much during the trials? Why or why not?

A6: Yes because the height of release changed the speed which in turn changed the momenteum.